Book Services

 

 

Just how do you feel on the subject of How to Install a Bathtub?

Setting up a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is readily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the task as well as fit trying it. As opposed to employing a specialist to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This short article will help you install a new bathtub in your bathroom if you have currently gotten a new tub and don't require to transform the setup of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Planning for the Setup

First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final setting.

 

 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your setup, after that the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather problematic because of the limited gain access to that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub until the spirit level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow outlet as well as the typical outlet for leakages.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been utilized a minimum of once as this will settle it into its last placement.

 

 

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in difficulties with moisture as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you enjoy more info about How to Install a Bathtub Yourself? Give a short review further down. We'd be pleased to see your responses about this page. In hopes to see you back again in the near future. Don't hesitate to take a moment to share this entry if you enjoyed reading it. Thank you for taking the time to read it.

Get Quote Now